Everything arrived together—the powered rod, lead, adapter, socket and tape. The box was packed neatly and nothing was missing.
Rotten-egg hot water? Swap the rod.
Powered Anode Rod · For Tank Water Heaters
A powered titanium anode rod for your water heater. It replaces the magnesium rod that wears away inside the tank — the rod that is usually behind hot water that smells of rotten eggs.
Free tracked shipping · usually 5–10 business days.
For tank water heaters with a hex-head anode rod on top (¾-inch NPT thread, 1-1/16 in hex). Not for tankless heaters, RV heaters, or tanks where the anode is part of the hot-water outlet. Needs a wall outlet near the heater.
Rather not do it yourself? Any plumber can fit it — it is the same job as swapping an ordinary anode rod.
A steel tank rusts from the inside unless something protects it. A magnesium rod does that by corroding first, until it is gone. A powered rod does it with a small electric current from the wall outlet, so the rod itself is not consumed. The illustration above is decorative.
The rod in your tank
Every steel tank water heater has an anode rod screwed into the top. It is usually magnesium, and its job is to corrode so the tank does not. In some water — well water most often — bacteria that live harmlessly in the tank react with the magnesium and make hydrogen sulfide gas, which is the rotten-egg smell. Softened water has a different problem: it uses magnesium rods up quickly, and a tank with no rod left starts to rust. The usual fix for both is the same: take the magnesium rod out and fit a powered one.
Six reasons
Fitting it
Switch the heater off at the breaker (or set a gas heater to off), close the cold-water inlet, and open a hot tap to release the pressure.
Unscrew the hex-head anode on top of the tank with the included 1-1/16 in socket. Old rods can be tight; a breaker bar or an impact wrench helps.
Wrap the threads with the included tape, lower the titanium rod into the port and tighten the head.
Connect the lead (red connector to the rod, ring terminal to the tank — see the guide below), turn the water back on and refill the tank, then plug in the adapter and switch the heater back on.
Not sure about doing it yourself? Any plumber can fit it for you.
Download the installation guide (PDF) — all nine steps, wiring and troubleshooting.
Why Tarn
| FYROST TarnTarn | Magnesium rodMagnesium | Aluminum-zinc rodAlu-zinc | |
|---|---|---|---|
| How it protects the tank | Electric current | Corrodes first | Corrodes first |
| Wears away | No | Yes | Yes |
| Linked to rotten-egg smell | No | Often | Less often |
| Needs a wall outlet | Yes | No | No |
| Socket to fit it included | Yes | Rarely | Rarely |
Straight answer
It is one part for one job. Here is the honest version.
Good to know
Tarn fits tank water heaters that have a separate hex-head anode rod on top, with a ¾-inch NPT thread and a 1-1/16 in hex — the usual arrangement on residential tanks. Look for a hex plug on top of the heater, sometimes under a plastic cap. If your anode is built into the hot-water outlet pipe, Tarn is not the right part.
It works the same way — a titanium rod that protects the tank with a small current from a plug-in adapter. The difference is mostly the brand name and how many years of cover are priced in. Tarn comes as a complete kit (socket and thread-seal tape included) with free shipping, a 1-year warranty and 60 days to try it. If it is not right for your heater, email us for a refund.
The rod is coated titanium on a stainless-steel head, with thread-seal tape on the ¾-inch NPT thread. The plug-in adapter stays outside the tank at the wall outlet; only its lead connects to the head on top of the heater.
Run the cold tap and the hot tap separately. If only the hot water smells of rotten eggs, the magnesium rod in the heater is the usual cause. If the cold water smells as well, the cause is in the water supply and a new rod will not change it.
If you are comfortable switching off the heater and using a socket wrench, yes. The stubborn part is loosening the old rod, which can be tight after years in the tank. A plumber can also fit it for you. Read the step-by-step installation guide (PDF) before you start.
The powered anode rod (titanium rod on a stainless-steel head), the plug-in adapter with its lead, a 1-1/16 in socket and a roll of thread-seal tape.
Yes. Softened water uses magnesium rods up quickly; a powered rod is not consumed, so there is nothing for softened water to use up.
The whole rod is under 14 in (35 cm) long, so it needs far less clearance than a full-length magnesium rod.
Tarn needs power to protect the tank. A short outage does no harm, but do not leave it unplugged.
Some manufacturers ask for their own replacement parts. If your heater is still under warranty, check its terms first.
Orders are processed within 1–2 business days and usually arrive in 5–10 business days, with tracking emailed as soon as your Tarn ships.
Sixty days from delivery: if Tarn is not right for your heater, email us for a refund of the purchase price. For a change-of-mind return you cover the return postage — see the refund policy.
The FYROST promise
Every water heater and every water supply is different — so take sixty days with it. If Tarn is not right for yours, email us for a refund of the purchase price. No restocking fees, no awkward questions.
What’s in the box
Old rod out, Tarn in, plug it in.
Sixty days to find out. If it isn’t right, you get your money back.
Free shipping · 60-day guarantee · 1-year warranty